![]() We hope we have provided you with the information you need to carry out a quick and trouble-free installation with perfect results. Comparez les prix pour Scala2 3-45 Akccde 1x200-240v 50/60hz - Grundfos : 98562862 pas cher de marque GRUNDFOS et dans la catégorie Pompe à eau sur 123comparer : les meilleurs sites classés par prix, stock, et livraison. This concludes our look at the 3-step installation process of the SCALA2 water booster pump. The easy set-up process is made possible by the intelligent pump control, which enables SCALA2 to detect any change in water pressure and adjust operation to compensate for these variations instantly. Simply fill the pump housing with 0.37 gallons of water, using the. If the pressure is adequate here, you can rest assured that it is perfect in all taps. SCALA2 is a self-priming pump, which means there is no need to fill the entire suction line. Simply use the control panel to set the required discharge pressure level and check the water pressure at the furthest tapping point – preferably a shower, as this is where the homeowner will experience the water pressure most directly. Then connect the pump to the rigid piping using the flexible hoses. To avoid this, we recommend placing vibration-damping feet underneath the booster and fixating all rigid pipes. But all pumps vibrate, and vibrations from a pump can be transferred to floors, walls and pipes, creating noise, if it’s not installed correctly. SCALA2 is one of the most silent boosters in its class. Once primed, connect SCALA2 to the power outlet and it will start automatically, delivering the default pressure of 44 psi throughout the system.Ī quick note on noise-reduction before we move on: If the pump has to boost water from a depth of below 19.6 feet, you may need to add another 0.37 gallons of water. ![]() Simply fill the pump housing with 0.37 gallons of water, using the extra large priming hole. SCALA2 is a self-priming pump, which means there is no need to fill the entire suction line. Start out by bolting the booster to the floor in the position you have marked.Ĭonnect the water pipes using the flexible connections - and tighten by hand. If the operating conditions check out, you are ready to install. You should also ensure easy access to a power outlet with the right supply voltage as well as a drain or a drip tray to lead away condensation if the surface is not resistant to water. However, we recommend always leaving enough space for service and maintenance. SCALA2 features a compact design, which means that it will fit tightly inside spaces such as kitchen cupboards. If the temperature drops below 32 degrees Fahrenheit, the water booster pump must be protected against frost. ![]() ![]() SCALA2 is fit for both indoor and outdoor installation, but the ambient temperature should not exceed 131 degrees Fahrenheit. This video will take you through the three basic steps of a successful installation: preparation, installation and set-up.īefore installing SCALA2, you will need to make sure that the operating conditions are suitable. The built-in pressure tank reduces the number of starts and stops in case of leakages in the pipe system, causing less wear on the pump.SCALA2 is a fully integrated water booster pump designed for easy installation. Max noise level at full load are 53 dB(A) Thanks to its hydraulic design, permanent magnet motor and water cooling, the pump is extremely low-noise, 47 dB(A) in typical use, which makes it suitable for indoor as well as outdoor use. The automatic reset function can be deactivated. Restarting will be attempted every 5 minutes 8 times, there after new restart attempt will occur every 24 hours. In case of dry running or similar alarm, the pump will stop. The pump features an automatic reset function. If exposed to dry running, water shortage or excessive temperature, blocked pump, for example in case of seizure or overload, the pump will stop automatically, thus preventing a motor burnout. This facilitates easy installation and start-up of the pump and provides more reliable water supply in installations where there is a risk of dry running and leakages in suction hose or pipes. Provided it is filled with water, the pump is able to lift water from a depth of 8 m in less than 5 minutes. Grundfos SCALA2 has all the components necessary to ensure a comfortable pressure:Īs it is self-priming, the SCALA2 is able to pump water from a level below the pump. Plug the pump into the power outlet and the pump will start. SCALA2 can be installed in three easy steps:ģ. SCALA2 incorporates integrated speed control enabling the keeping of the perfect pressure at the taps, meaning that the pump performance will increase with increasing demand. Grundfos SCALA2 is a fully integrated, self-priming, compact waterworks for pressure boosting in domestic applications.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |